Kỹ thuật

Chức năng của các bộ phận trong máy nén khí Kobelco

Chức năng của các bộ phận trong máy nén khí Kobelco

Máy nén khí Kobelco là một thiết bị phức tạp với nhiều bộ phận hoạt động cùng nhau để tạo ra luồng khí nén phục vụ các nhu cầu công nghiệp khác nhau. Dưới đây là mô tả chi tiết về chức năng của các bộ phận quan trọng trong máy nén khí Kobelco.
Bảo dưỡng máy sấy khí tác nhân lạnh máy nén khí Kaeser dóng ASK

Bảo dưỡng máy sấy khí tác nhân lạnh máy nén khí Kaeser dóng ASK

The refrigeration circuit is fully hermetically sealed and needs no maintenance. Repairs may only be carried out by certified personnel/ Mạch làm mát là mạch kín và khong cần bảo dưỡng. Chỉ để người có chuyên môn sửa chữa.
Cách thay thế lọc tách dầu máy nén khí Kobelco AG 720A-37

Cách thay thế lọc tách dầu máy nén khí Kobelco AG 720A-37

Lọc tách dầu là một trong 3 loại lọc cần thay thế định kì trong máy nén khí. Lọc tách có chức năng lọc tách dầu ra khỏi máy nén khí. Thay thế lọc tách dầu là một trong những công đoạn bảo dưỡng của máy nén khí Kobelco.Lọc tách dầu của máy nén khí Kobelco AG 720A-37 được thiết kế rất chắc chắn. Được cố định bằng vít xung quanh tránh tình trạng áp lực trong lọc tách dầu lớn văng lọc tách ra ngoài như dạng xoáy.
Bảo dưỡng, thay thế lõi lọc đường ống máy nén khí Kobelco

Bảo dưỡng, thay thế lõi lọc đường ống máy nén khí Kobelco

Bụi bẩn sẽ đi vào máy nén khí trong quá trình hoạt động, đặc biệt khi bụi bẩn được chứa trong dầu, nó sẽ gây ảnh hưởng nghiêm trọng đến các van, motor và các thiết bị khí nén khác. Việc kiểm tra và thay thế lõi lọc phải được diễn ra thường xuyên để có thể bảo vệ máy nén khí.Lọc phải được vệ sinh sạch sẽ để tách các chất bẩn, cắn, cặn vướng vào, nếu không sự lưu thông của dòng khí qua bộ lọc sẽ hạn chế.

Compressors equipment repairs

Thứ bảy - 22/12/2018 05:19

Air screw compressors are in the important position in the industrial process, therefore all aggregates breaks and troubleshooting affecting to industrial process in general and have not expected results. Air screw compressors quality and advantages are undeniable, but every mechanism is run-out eventually, some parts operate not stable, some are out of operation at all.
 

compressors equipment repairs, dong co cua may nen khi,bao duong may nen khi, sua chua may nen khi, bảo dưỡng máy nén khí, sửa chữa máy nén khí, air compressor repair service, air compressormaintanece service


 It is impossible to avoid this situation, but it is possible to decrease expenses for the air screw compressors repairs. The simplest and effective ways is to maintenance the compressors equipment in time and not just replace air and oil filters, separator and oil, but make diagnostics of the separate parts addicted to the run-out. Careful compressor equipment revision and diagnostics allow to find small problems and avoid big problems, hence have less expenses and time for the adjustment and repair of the equipment.

The possible variants of the air end break include:

1. Air end breakage

Air end is the heart of the compressor, it is the most important and most expensive part, therefore it is very important to care about it and avoid replacement of the air end. In case of replacement, the total amount of new air end is about 70% of total price the compressor. But it is the worst variant. Please see chapter “Air end repairs” to know regarding possible variants of block the unit. Unfortunately, if air end is blocked, this problem will not be solved just replacement of the spare parts. It is necessary to make diagnostics, to understand what repairs have to be released.

2.  Drivebreakage

In compressor with belt drive, the possible case is belt rupture. The belt is run-out during operation because of abrasion and dust in the air. Usually similar problems are not the case of negative consequences and it is necessary just to replace the belt.
Compressor with gear drive needs more efforts. The most common problem is gear drive block, run-out the gears. These parts and their repairs are quite expensive.
And, at last, compressors with direct drive. The direct drive failure can be connected with flexible coupling break. This coupling is providing connection between drive and air end. In this case the broken part has to be replaced and compressor has to be inspected and checked.

 

thay bi may nen khi truc vit hanshin han quoc, sua chua may nen khi truc vit hanshin, bao duong may nen khi truc vit hanshin,bao duong may nen khi, sua chua may nen khi, bảo dưỡng máy nén khí, sửa chữa máy nén khí, air compressor repair service, air compressormaintanece service

3.Electricalmotorbreakage

There are some possible problems: the most expensive is replacing of the electrical motor and more effective is motor winding recovery. However it is possible to avoid the electrical motor break by replacing the motor bearings after vibration appears.

4. Frequency inverter is out of operation

The frequency inverter is designed for the motor speed regulation and offer to decrease power consumption significantly. During the time frequency inverter also can out of the order because of damage the cable, pollution, overheating, or other cases. Almost always they can be repaired, so it is not necessary to replace the whole device.

5. Controller is out of operation:it is necessary make settings of the all compressor parameters, replace all power section elements which are out of order (starters, rely), adjustment one or group of the compressors in adjusted mode.

Our company implement the compressor equipment repairs: ABAC, Dyna, Kobelco, Fusheng, Hitachi, Hanshin, Micos, Swan, Ingersoll Rand, Boge, Atlas Copco, Sullair, Kaeser, Kyungwon, Compair, Puma, Buma, Ceccato, Airman, Quincy, SCR, Mitsui seiki, Swan…

Please send your requests to our e-mail address:  info.mipuco@gmail.com or contact us +84 46294 82 82.

                                                                                               Mr : Phu Nguyen

Thông Tin Chi Tiết

Tổng số điểm của bài viết là: 0 trong 0 đánh giá

Click để đánh giá bài viết